The Fundamentals of Plumbing Skills for Bathtub Installation

Visit My Website

What're your thoughts on Installing A Bathtub?


Installing A Bathtub
Mounting a bath tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is additionally a moderately difficult project. If the old tub is readily easily accessible, the job can relocate quickly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to vacate the old tub and also set in the brand-new one. Ensure you have certified yourself for the work and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed task, it is much better to consider using one before you start. Opportunities are you may require an expert plumber to make tube connections.
This short article will aid you install a new bath tub in your bathroom if you have currently bought a new tub and don't require to alter the arrangement of your previous water pipelines.
Your devices as well as material checklist must comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be quite bothersome because of the limited access that is often the situation.
    Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
    Prior to going on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end provides a connection to the existing supply pipelines.
    If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next, place the faucet in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Safeguard the faucet in place with the supplier given backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap ports. The former type ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Bathtub


    Utilizing both wood boards under its feet, place the bath tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 small factors.
    The following goal is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub until the spirit level reads degree.
    To mount taps, fit the bottom of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the same for the other tap.
    Turn on the water system and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill the tub and also examine the overflow outlet and also the normal electrical outlet for leaks.
    Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the tub has been used at least once as this will certainly resolve it right into its final position.

    Preparing for the Installation


    First of all, the supporting structure provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid stress on the bathtub.
    Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final setting.

    Tiling Around the Bath tub


    In the area where the bath fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall in between the bath and also the tiling, bring about difficulties with moisture and also feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not take into account this motion before securing.
    Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly offered on the market. It is recommended to fit the tiles using water-resistant or water-proof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I stumbled upon that piece of writing on How to Install a Bathtub Yourself when scouting around the internet. Are you aware of another person who is excited about the subject? Feel free to promote it. Thank you for taking the time to read it.


    View Website

    Leave a Reply

    Your email address will not be published. Required fields are marked *